XDMA7715
INSTALLATION/OWNER'SꢀMANUAL
®
AM/FM/CD/MP3/WMA/Bluetooth ReadyꢀReceiverꢀ
withꢀ2-StepꢀMotorizedꢀDetachableꢀFace
READY
XDMA7715ꢀINSTALLATIONꢀ
WiringꢀDiagram
BLACK 8-pin Female Mini-DIN
Front Preamp Output
BTM60 Connection (sold separately)
Yellow
Auxiliary Input
Subwoofer Preamp Output
Antenna Connector
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDMA7715 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDMA7715ꢀOPERATIONꢀ
ControlꢀLocationsꢀ-ꢀReceiver
2
3
4
5
6
7
8
9
10
11 12
13
1
25
24 23
22 21 20
19
18
17 16 15
14
Talk/Redial
Display/Key 0
Tuner Scan/Key 8
EQ/Key 9
1
2
14
Mode/Search
Mute/End Call
Preset 2/Repeat
Preset 1/Folder Down
Open
15
16
17
18
19
20
21
3
Key 0
4
Band/Play/Pause/Key *
Infrared Sensor
Power
5
6
Volume
7
Eject
Preset 5/Menu
8
9
Preset 6/Folder Up
Return/Key 7
Tune/Track Down
AS/PS/Enter/Key #
Tune/Track Up
22 Preset 4/Intro
10
11
12
13
23 Preset 3/Random
24
25
Reset
Audio/Setup
Note: Function keys 7, 8, 9 and 0 apply to Bluetooth and MP3/WMA operation only.
4
XDMA7715ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
1
2
3
4
5
21
20
6
19
7
8
18
17
9
16
15
10
11
14
12
13
Power
Volume Up
1
2
Mute/End Call
Scan/Key 8
12
13
14
15
16
AS/PS/Enter/Key #
Audio/Setup
3
Talk/Redial
4
Return/Key 7
Preset 5/Menu
Tune/Track Up
Display/Key 0
Volume Down
Preset 3/Random
Preset 2/Repeat
Preset 6/Folder Up
EQ/Key 9
5
6
17 Preset 4/Intro
18
19 Mode/Search
7
Preset 1/Folder Down
8
9
Tune/Track Down
20
21
10
11
Band/Play/Pause/Key *
5
XDMA7715ꢀOPERATION
GeneralꢀOperation
Theꢀfrontꢀpanelꢀisꢀsemi-permanentlyꢀattachedꢀduringꢀ
FrontꢀPanelꢀNote:
assembly.ꢀPleaseꢀreferꢀtoꢀtheꢀseparateꢀyellowꢀinstructionsꢀ
(beforeꢀinstallation)ꢀtoꢀmakeꢀtheꢀfrontꢀpanelꢀremovable.
With the unit off, press EJECT to allow the front panel to slide
down. Gently squeeze the release tab located on the bottom
center underside and pull front panel down and away from
unit to remove. To install, insert left side first, then push right
side to secure.
FrontꢀPanelꢀRemoval
Press POWER or any other button (except EJECT or OPEN)
to turn the unit on. Inserting a disc will turn the unit on
automatically. Press POWER to turn the unit off.
PowerꢀOn/Off
Mode
Press MODE to select between AM/FM, CD player, auxiliary
input and Bluetooth (optional). Modes of operation are
indicated in the display.
NOTE: CD and Bluetooth modes will not appear unless a CD
is inserted or BTM60 (Bluetooth module) is attached.
Adjust volume using rotary encoder (00-46).
Volume
Press and hold POWER for 3 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Programmableꢀ
Turn-OnꢀVolume
PresetꢀEQꢀCurves Press EQꢀto select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Display When in AM/FM, CD, or AUX mode:
Press DISP to select between clock and radio frequency
(tuner mode), clock and CD elapsed time/track (CD mode or
clock and AUX (AUX mode).
SetꢀtheꢀClock With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE
to adjust the hours and
to adjust the minutes. Press DISP momentarily to
nn
TUNEꢀ
ll
save the selected time.
6
XDMA7715ꢀOPERATION
GeneralꢀOperationꢀ-ꢀSetupꢀMenu
12/24-hourꢀClockꢀ The clock will display 12-hour AM/PM time in USA frequency
:
spacing mode (PM 10 00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
SetupꢀMenuꢀ Press and hold SETUP for more than 3 seconds to access
the setup menu. Press SETUP momentarily to select
between the menu functions and rotate the rotaryꢀencoder
left/right to adjust or activate the desired function.
MenuꢀFunction
LoudnessꢀCurve LOUD OFF Disables the loudness function.
LOUD ON Enables the loudness function. Activating this feature
Options
Action
will enhance the bass and treble frequencies when
listening to music at low volumes.
TunerꢀFrequencyꢀ FREQ USA Programs the unit to USA tuner spacing.
Spacing
(200kHz for FM and 10kHz for AM)
FREQ EUR Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
ClockꢀDisplay
CLK OFF
Programs the unit to not display the clock when the
power is off.
CLK ON
Programs the unit to display the clock when the power
is off.
AuxiliaryꢀMode
AUX ON
Enables access to auxiliary mode.
Disables access to auxiliary mode.
Disables the confirmation beep.
AUX OFF
BEEP OFF
BEEP ON
LOC OFF
LOC ON
Beepꢀ
Confirmation
Enables the confirmation beep.
Local/Distanceꢀ
Tuning
Activates Distance tuning.
Activates Local tuning for strong station reception only.
SubwooferꢀMode SB-W OFF Disables the subwoofer RCA output.
SB-W ON
Activates the subwoofer RCA output. Subwoofer control
will be available in the audio menu.
Powerꢀonꢀ
Message
MSG OFF
MSG ON
DEMO ON
Disables power on message.
Enables power on message to be displayed.
Enables the "BT READY" message.
Demonstrationꢀ
Mode
DEMO OFF Disables the demonstration mode.
7
XDMA7715ꢀOPERATION
GeneralꢀOperation
Press AUDIO momentarily to select between Volume
(default), Bass, Treble, Balance, Fader and *Subwoofer.
Audio
VOLUME
BASS TREBLE
BALANCE
FADER
*SUBWOOFER
Press AUDIO until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Bass
Treble
Press AUDIO until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press AUDIO until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Balance
Press AUDIO until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Fader
Press AUDIO until SUB appears then rotate encoder
*Subwoofer
left/right to adjust (0 minimum / +12 maximum).
Individual Bass and Treble settings are retained in memory
for AM, FM, CD, AUX and Bluetooth modes. This allows you
to save the Bass and Treble settings separately for each
mode.
SourceꢀAudioꢀMemory
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
Press RESET upon initial installation or if abnormal
operation occurs. The reset button is located behind the
faceplate.
Reset
*Note
Subwoofer option must be enabled before it will appear in
the audio menu. Refer to page 7 for details.
8
XDMA7715ꢀOPERATIONꢀ
AM/FMꢀTunerꢀOperation
SeekꢀTuning Press TUNE
or TUNEꢀ
next strong station.
momentarily to seek the
nn
ll
ManualꢀTuning Press TUNE
or TUNEꢀ
for more than 2 seconds,
nn
ll
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
or TUNEꢀ
momentarily to
nn
ll
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for 5
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
ScanꢀTuning Press SCN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCN again to cancel.
Bandꢀ Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
StoringꢀandꢀRecallingꢀ Up to 18 FM stations and 12 AM stations can be stored. To
StationꢀPresets store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Note: Function keys 7, 8, 9 and 0 apply to Bluetooth and
MP3/WMA operation only.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Local tuning is activated during the initial band scan.
AutomaticallyꢀStoreꢀ
Stations
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
PresetꢀScan
9
XDMA7715ꢀOPERATION
CDꢀPlayerꢀOperation
With the label facing up, insert a standard size CD into the
InsertꢀCD
CD slot. The CD will automatically begin playback.
Press EJECT to eject the CD. The unit will change to
previous mode of operation (AM, FM or auxiliary input).
If the disc is not removed within 10 seconds, the unit will
reload the disc. The unit does not have to be turned on to
eject CD.
EjectꢀCD
Press TRACKꢀ
track. Press TRACK
current track. Pressing TRACK
beginning of the previous track.
to skip to the beginning of the next
TrackꢀSelect
ll
to return to the beginning of the
nn
again skips to the
nn
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
FastꢀForwardꢀandꢀReverse
ll
nn
Press
Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
Pause
Scan
l
l
Press INTꢀto play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Repeat
Random
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between AM/FM tuner, CD player, auxiliary input
and Bluetooth modes and when the unit is turned
off/on.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CD-R/CD-RWꢀCompatibility
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDMA7715ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
When an MP3/WMA encoded disc is first inserted,
PlayingꢀanꢀMP3/WMAꢀDisc
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
DisplayingꢀInformation
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
ꢀꢀ
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the album name is displayed.
ꢀTitleꢀIconꢀꢀ
ArtistꢀIconꢀꢀ
AlbumꢀIconꢀꢀ
FolderꢀIconꢀꢀ
This icon will illuminate when the directory name is
displayed.
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
CharacterꢀSupport
*Song title, Artist Name, and Album name, will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDMA7715ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Refer to the following button function table when selecting, searching or
navigating MP3/WMA files and folders:
MP3/WMAꢀButtonꢀFunctionꢀTable
Button
Function
SRCH
Direct Select, Search and Navigate Modes
Enter/Confirm
A, B, C, 1
Preset #1
Preset #2
Preset #3
Preset #4
Preset #5
Preset #6
Key #7
D, E, F, 2
G, H, I, 3
J, K, L, 4
M, N, O, 5
P, Q, R, 6
S, T, U, 7
Key #8
V, W, X, 8
Key #9
Y, Z, /, 9
Key #0
-, _, +, 0
AUDIO
Character Shift
Character Select (A, B, C ~ 8, 9, 0)
Character Backspace
Rotary Encoder (rotate)
MUTE
DirectꢀSelect,ꢀSearchꢀandꢀ
NavigateꢀModesꢀ
Press SEARCHꢀfor more than 3 seconds, to select between
the following modes:
• Direct File Select
• Alphanumeric File or Folder Search
• File or Folder Navigate
DirectꢀFileꢀSelect
Stepꢀ1
Press SEARCHꢀfor more than 3 seconds, then release.
“MP3 T " or “WMA T ” will flash in the display. Use the
*
*
buttons in the above table (3 keystroke maximum input),
or the rotary encoder to enter the desired file number.
Stepꢀ2
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
12
XDMA7715ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AlphanumericꢀFileꢀ Press SEARCHꢀfor more than 3 seconds, then release.
ꢀorꢀFolderꢀSearch Press SEARCHꢀagain, an " " will flash in the display.
*
Stepꢀ1 Use the buttons in the table on page 12 (32 character
maximum input) or the rotary encoder to enter the desired
alphanumeric search characters. Press AUDIO to advance
one character to the right.
Stepꢀ2 Press
to initiate the selected alphanumeric search.
Stepꢀ3 Turn the rotary encoder to preview the search results.
If the search returns a folder, the icon will illuminate.
Stepꢀꢀ4 Press
to select the desired file or folder. If a folder is
selected, "/ꢀ/" will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder.
Stepꢀ5 Press
Note:
to select the desired file within the folder.
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
File/FolderꢀNavigate Press SEARCHꢀfor more than 3 seconds, then release.
Stepꢀ1 Press SEARCHꢀagain two times to navigate files/folders
on the disc. The current folder name will scroll one time
followed by available files and folders.
Stepꢀ2 Turn the rotary encoder to preview files/folders in the
current folder. If a folder is selected, the
icon will
illuminate.
Stepꢀ3 Press
to select the desired file or folder. If a folder is
selected, "/ꢀ/ꢀ" will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder.
Stepꢀ4 Press
to select the desired file within the folder.
*FolderꢀAccess When navigating folders (and “/ꢀ/“ is displayed), press
(Upꢀꢀoneꢀlevel)ꢀ AUDIO to access the previous level (up one level).
*Only available on MP3/WMA discs recorded with more
than one folder.
13
XDMA7715ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
NavigatingꢀNote
*FolderꢀAccessꢀ
FileꢀRepeat
After navigating by direct select, alphanumeric search or
file/folder navigate modes, the track number and elapsed
time will be displayed by default. Press DISP momentarily
to select clock, track name, directory name, title, artist and
album.
Press
Press
to select the previous folder.
to select the next folder.
*Folder access is only available on MP3/WMA discs recorded
with more than one folder.
Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
FileꢀRepeat
Press RPT for more than 2 seconds to consecutively repeat
(CurrentꢀFolderꢀOnly)
all files in the current folder only. The
the display when in folder repeat mode.
Press RPT again to cancel.
icon will appear in
DiscꢀRandom
Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
FolderꢀRandom
Press RDM for more than 2 seconds to play all files in
current folder only in random order. The
in the display when in folder random mode.
Press RDM again to cancel.
icon will appear
DiscꢀIntro Press INT momentarily to play the first 10 seconds of each
file on the entire MP3/WMA disc. Press INT again to cancel.
FolderꢀIntro Press INT for more than 2 seconds to play the first 10
seconds of each file in the current folder only. The
will appear in the display when in folder intro mode.
Press INT again to cancel.
icon
Note:
File repeat (current folder only), folder random and folder
intro is only available on MP3/WMA discs recorded with
more than one folder.
14
XDMA7715ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
CompatibleꢀRecordingꢀ
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
15
XDMA7715ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ
Information
An internal buffer provides ESP (Electronic Skip Protection) to
virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3
8kHz ~ 48kHz
32kHz ~ 48kHz
WMA
TransferꢀBitꢀrates
MP3
8kbps ~ 320kbps constant
Variable bit rates
WMA
32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay
ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
RecommendedꢀSettings
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
16
XDMA7715ꢀOPERATION
Bluetooth®ꢀOperationꢀ(Optional)
Overview
Connecting a Bluetooth device requires first connecting the Dual BTM60 module (sold
separately). When connected to a Dual Bluetooth Ready head unit, the BTM60 supports
the HFP (hands-free profile), A2DP (advanced audio distribution profile) and AVRCP (audio
video remote control profile).
Preparation
Before you can use a mobile device with this head unit, it must be connected and
authenticated - commonly referred to as "pairing" a device. Please make sure that
Bluetooth is activated on your mobile device before you begin the pairing process. Refer
to the owner's manual of your mobile device for more details.
BluetoothꢀPairing
1) To pair a Bluetooth enabled mobile phone to your head unit, press on the head unit
or BTM60, or press MODE until "DUAL_BTM60" is displayed.
2) Press and hold on the head unit or the BTM60 for 5 seconds, until "PAIRING"
is displayed, the Bluetooth icon will flash every second. The head unit will begin to
broadcast a signal for 60 seconds.
3) Complete the pairing from the Bluetooth menu of your mobile device by searching for
new devices. Please refer to your mobile device instructions for further information on
Bluetooth pairing and connections. The Bluetooth icon will illuminate solid.
TheꢀBTM60ꢀdeviceꢀnameꢀisꢀ"DUAL_BTM60."ꢀꢀ
TheꢀpasswordꢀforꢀtheꢀDUALꢀBTM60ꢀisꢀ1234.ꢀꢀ
ConnectionꢀNotes
•If ACNT is set to OFF, you must press to connect after pairing.
•From Bluetooth standby mode, press MUTEꢀto disconnect your mobile device from the
BTM60.
•From Bluetooth standby mode, press to reconnect your mobile device to the BTM60.
•To connect a different mobile device, the currently connected mobile device must be
disconnected. If this device has been paired previously, you may reconnect using the
mobile device's Bluetooth menu, or repeat the above pairing instructions.
GeneralꢀNotes
•Due to the differences in Bluetooth technology, some mobile devices may be
incompatible or function improperly when used with the BTM60.
•The BTM60 will store the last eight (8) devices that have been paired in its memory. If
more than eight devices are paired, the head unit will remove the oldest device from its
memory and that device will have to be paired again.
17
XDMA7715ꢀOPERATION
Bluetooth®ꢀOperationꢀ(Optional)
Description
Function
Press once. An "_" will appear on the display.
Input the desired phone number using the 0-9, *, # buttons on the
head unit front panel. Press to begin dialing.
MakingꢀaꢀPhoneꢀCall
A phone call may also be placed from your mobile device using
the keypad, phone book or speed dial. When a call is placed from a
mobile device, “DIALING” will appear on the head unit display.
To enter last number dialing mode, press , then press a second
time. The head unit will display "Last Number Dialing."
Press KEYꢀ0 to cycle through the received, dialed or missed call
LastꢀNumberꢀDialing categories. Rotate the rotaryꢀencoder to cycle through the last 5 calls
in the selected category.
Press to begin dialing the selected number. “DIALING” will appear
on the head unit display.
If an incoming call is detected, the head unit will automatically switch
to Bluetooth mode, muting any current audio.
The incoming phone number will scroll across the display, the phone
icon will flash on the display, and a ring tone will be audible from the
vehicle speakers. See Bluetooth Settings for speaker configurations.
ReceivingꢀaꢀPhoneꢀ
Call
NOTE: The ring audio level will depend the mobile device and head
unit ring volume and audio settings. If the ringer on the mobile device
is off, you may not hear an incoming ring tone.
Press on the head unit or BTM60 to receive a call. The phone icon
will illuminate solid.
To refuse an incoming phone call, press and hold MUTE for 3
seconds.
RefusingꢀaꢀCall
The head unit will display the elapsed time of the phone call.
The rotaryꢀencoder will adjust the volume of the call.
DuringꢀaꢀPhoneꢀCall
Press MUTE to select between microphone on (MIC ON) and
microphone off (MIC OFF).
To transfer the phone call between the head unit and the mobile
device, press and hold DISP for 3 seconds during a call. Tip: transfer
audio to your mobile device before turning the head unit off.
AudioꢀTransfer
When a second call is incoming, press to activate call waiting. The
current call will be placed on hold, and the second call will be active.
Press again to return to the first call.
CallꢀWaiting
CallꢀHold
Press TALK to place the current call on hold. To resume the phone
call, press TALKꢀagain.
Hold MUTE for 3 or more seconds to end a call.
EndingꢀaꢀPhoneꢀCall
If the phone call was received, the head unit will return to previous
mode when call is ended.
18
XDMA7715ꢀOPERATION
Bluetooth®ꢀSettingsꢀ(Optional)
Options
Action
Menu Function
BT ON
Enables the BTM60 Bluetooth Interface Module (sold
separately). The Bluetooth icon will flash every 10
seconds.
BluetoothꢀModeꢀ
BT OFF
Disables Bluetooth support.
ACNT ON
Allows the BTM60 to automatically (re)connect to the
most recently connected mobile device. Note: Some
mobile devices do not support this feature.
AutoꢀConnect
ACNT OFF
AANS OFF
AANS ON
Disables the auto connect feature. You must press
every time to connect a mobile device.
Disables the auto answer feature. Press to receive
an incoming call.
AutoꢀAnswer
All incoming calls will be answered automatically
- without notification.
SPK 2-CH
SPK 4-CH
Directs the Bluetooth audio to the front speakers.
Directs the Bluetooth audio to all 4 speakers.
BluetoothꢀAudio
BluetoothꢀStreamingꢀAudioꢀOperation
(AVꢀMODE)
The BTM60 supports A2DP wireless streaming audio from your Bluetooth mobile device
directly to your head unit. You can also control your music from the front panel of the head
unit using AVRCP.
To stream music to your head unit, your mobile device must support the following criteria:
• A2DP profile to stream audio
• AVRCP profile to control your music. Check the owner's manual or manufacturer
of your device for compatibility.
• Streaming audio must be enabled from your mobile device. This option will vary
depending on the device. Example: "Set as wireless stereo."
• Disabling AV MODE must be done from your mobile device.
After enabling streaming audio from a compatible mobile device, the head unit will display
"AV MODE." The following functions can be used to control music:
• The
• The
• The
button will skip to the next available audio track.
button will skip to the previous audio track.
II button will toggle between play and pause during playback.
ll
nn
/
l
• The MUTE button will stop the audio playback.
NOTE: If you are experiencing problems with these functions, try playing music from the
mobile device. On some mobile devices, it may be necessary to control the music from the
device.
19
XDMA7715ꢀWARRANTY
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
You may also have other rights which vary
from state to state.
Whatꢀtoꢀdo?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer and
used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered:
software, installation/removal costs, damage
resulting from accident, misuse, abuse, neglect,
product modification, improper installation,
incorrect line voltage, unauthorized repair or
failure to follow instructions supplied with the
product, or damage occurring during return
shipment of the product. Specific license
conditions and copyright notices for the
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
20
XDMA7715ꢀOPERATION
Troubleshootingꢀ
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each Insulate all bare speaker wires
other or touching chassis ground
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or backstrap Check mounting sleeve and
is not secure
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
Press eject or RESET
Press eject or RESET
Focus error or disc is in upside down
ERROR-02ꢀappearsꢀ
onꢀdisplay
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that
are not copy-protected
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
NOꢀFILEꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Write disc using valid audio
files with .mp3 or .wma file
extensions
INVALIDꢀappearsꢀ
onꢀdisplay
CD mechanism position out of alignment
CD transit screws still in place
Press and hold EJECTꢀfor 3
seconds to reset CD mechanism
position
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws located
on top of the unit
Pairing attempt has exceeded 60 seconds Retry pairing sequence. Pairing
must complete within 60
seconds.
PAIRINGꢀFAILEDꢀ
appearsꢀonꢀtheꢀdisplay
Phone is not setup correctly to connect to
a bluetooth hands free device.
Check the owner's manual
for instructions on enabling
Bluetooth.
Bluetooth device is not compatible withꢀ
the BTM60
Contact technical support for
more information.
Reset the BTM60 to clear the memory
of previously paired mobile devices and
to clear recent dialed/missed/received
phone calls from memory
From Bluetooth standby mode,
press and hold MODE for BTM60
reset.
BTM60ꢀreset
21
XDMA7715ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Operating voltage: 11-16ꢀVDC,ꢀnegativeꢀground
Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVolts
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
22
XDMA7715ꢀOPERATION
FCCꢀCompliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
23
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2010 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and or other countries.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Namsung is under license.
Other trademarks and trade names are those of their respective owners.
NSA0210-V03
|