ContourHD
Wearable Camcorder
Product Guide
Quick Start
About the
Camera
i
d
h
b
c
j
a Power Button
b Battery Status
c Record Button
d Rotating Lens
e Record Status
g
a
k
f
Memory Status
l
e
f
g HD/SD Switch
h USB
or
i
j
Charge Indicator
Battery Latch
k Battery Slot
MicroSD card
l
1
Getting Ready
Power Up
s
Open the back door.
s Push power button.
s Insert battery with (+)
aligned and close latch.
s Align back door slightly
above camera and slide
down until it locks in.
2
s Camera beeps and lights turn off.
s You are ready to record.
Note: Power up with record switch
forward to enable silent mode.
Record
s Start: slide switch forward.
s Stop: slide switch back.
s Congrats, your first video!
stop
start
Share
s Then import, clip and share
your videos…
s Install Easy Edit Software
directly from MicroSD card
provided or download at:
software.
s Connect camera to computer
with USB cable.
s Set date and time on your
camera using the Easy Edit
Software
Note: HD is beautiful but some
computers cannot play smooth
HD video.
for the latest information on
computer requirements.
3
Memory
s 2GB microdSD card included. Accepts up to 16GB microSD (SDHC
Compatible). Note: Always power off before ejecting card.
s Use switch under back door to select video resolution.
HD: Amazing clarity
SD: Fast Action
1280 x 720 at 30fps
30 min avg record time/GB
Wide angle lens: 135 deg.
848 x 480 at 60 fps
60 min record time/GB
Wide angle lens: 110 deg.
Power
Recharge
Power Off
s Connect to computer with
USB cable.
s Press and hold power button
for 3 seconds.
s Red light indicates charging.
s Charge complete when
camera beeps and red light
turns off. (about 4 hrs)
4
s Double beep & lights turn off.
Note: Camera automatically turns
off after 15 min of inactivity.
Status
Press power button to check status.
s Memory / Battery Available
Green > 80%
s Record Status
Green = ready
Yellow 20-80%
Red = recording
Red < 20%
Flashing = memory full or corrupt
Error Conditions
s Time invalid: Memory/battery flash red at power on.
s Memory full: (3) beeps, recording stops.
s Memory corrupt: (3) beeps, shuts off.
s Battery dead: lights flash, beeps, shut off.
s No beeps: camera in silent mode.
5
Flat Surface Mount
s Unhook leash on base and loop
through camera.
s Slide camera onto rails until
completely forward.
s Adhere mount to flat
surface (top or side of
helmet recommended).
s Hold base, pull camera
away, rotate to align,
and press into mount to
reattach.
6
Goggle Mount
s Slide camera on rails until completely forward.
s Press thumb on large tab (top of mount)
and pull camera away.
s Slide goggle
strap into base.
s Align vertical
angle of
camera.
s Snap rails back
into mount
over strap.
7
Align
• Press power button to activate lasers.
• Aim at your hand, a wall, or other object.
• Rotate lens to align lasers horizontally.
• Remove and reorient mount rails to adjust mount
angle. Aim a little high for the best shot.
8
Tips & Troubleshooting
We want to help you have a great ContourHD1080p experience
so please contact us with any questions you have.
Hours: Monday – Friday (9am to 6pm PST)
Toll Free: 866.397.6920 (USA)
International: 206.792.5226
Email: support@vholdr.com
9
Cautions and Warranty
This Important Product Information Guide contains regulatory, safety, handling,
disposal and recycling information, as well as the 180-day limited warranty
for your ContourHD Camera.
Read all safety information below and operating instructions before using
ContourHD Camera to avoid injury. For detailed operating instructions and the
WARNING: Failure to follow these safety instructions could result in fi
re,
electric shock, or other injury or damage.
Battery handling
The lithium-ion battery may present a hazard if mistreated. Do not
disassemble, crush, or puncture the lithium-ion battery. Do not immerse
battery in water and store in a cool dry place when not in use. Do not use or
leave battery near a heat source or in direct sunlight.
10
ContourHD uses a rechargeable lithium-ion, 3.7V, 1050mAh battery. Do not
use batteries other than those specifically designed for the ContourHD. Use of
any other battery may invalidate the warranty provided by Twenty20, Inc. and
may present a risk of fire or explosion.
To charge, only use the ContourHD USB Cable with a high-power USB port on
a computer or other device that is compliant with the USB 2.0 or 1.1 standards,
or the ContourHD wall, car, or battery charger.
Disposal information
Do not dispose of either the ContourHD Camera or lithium-ion battery in a
fire. Dispose of batteries in accordance with local laws and regulations.
Correct Disposal of this Product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device,
please use proper return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
11
FCC Information
ContourHD Wearable Camcorder
Model: 1200
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modification to this unit not expressly approved by
party responsible for compliance could void the user’s authority to operate
the equipment. Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and if not installed and used in accordance
with instructions, it may cause harmful interference to radio communications.
There is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
12
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
s
s
s
Reorient or relocate the receiving antenna.
Increase separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
s
Consult the dealer or an experienced radio/TV technician for help.
The CE symbol on your ContourHD camera indicates that it is in
compliance with the Safety of Laser Products, Electromagnetic
Compatibility (EMC) directive, and Limits and Methods of Measurement of
Radio Interference Characteristics of ITE.
Industry Canada
This Class B device meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du
Reglement sur le materiel broulleur du Canada.
13
Laser notice
ContourHD is a Class II laser device. Laser radiation is emitted from the
ContourHD when using the lasers for alignment. Please use caution and
do not stare directly into the beam or point at others.
Repairing or modifying
Never attempt to repair or modify ContourHD Camera yourself. Disassembling
ContourHD Camera, including the removal of external screws, may cause
damage that is not covered under the warranty. The ContourHD Camera does
not contain any user-replaceable parts, except the MicroSD card and battery.
RoHS
ContourHD and ContourHD 1080 wearable camcorders comply with the
European Union’s R0HS directive 2002/95/EC and similar regulations that
may be adopted by other countries for European Sales.
14
TWENTY20, INC. LIMITED WARRANTY
Twenty20, Inc. (“Manufacturer”) warrants to the original end user
(“Purchaser”) that for the 180 days (“Warranty Period”), the ContourHD
Wearable Camcorder (excluding any third party software) and accessories
(“Product”) will be free from defects in materials and workmanship when
properly installed and used for its intended purpose and in its intended
operating environment. This warranty does not apply to any Product that
has been: (i) altered, repaired or modified; or (ii) damaged or destroyed by
accidents or similar events or by any intentional, reckless or negligent acts
or omissions of any party. In the event of a defect, return the Product to the
original place of purchase or Manufacturer, but only after instructed to do
so by Manufacturer. Purchaser shall ship and bear the cost of shipping the
Product to Manufacturer and Manufacturer shall bear the cost of shipping the
Product back to Purchaser after the completion of service under this limited
warranty. Purchaser’s exclusive remedy and Manufacturer’s entire liability
under this warranty will be for Manufacturer at its option to repair or replace
the Product or refund purchase price less any rebates. Manufacturer does not
warrant against loss of any data (including data stored on Product returned
15
to Manufacturer for service), and assumes no liability for such loss. Purchaser
assumes all liability, and as such releases Manufacturer from any liability, for
any accident, injury, damage, death, loss, illegal activity or any other claim that
may occur resulting from or during use of the Product, whether or not such
use is foreseeable by Manufacturer.
ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY. ALL OTHER EXPRESS OR IMPLIED CONDITIONS,
REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow
limitations on how long an implied warranty lasts, so the above limitation may
not apply to Purchaser. This warranty gives Purchaser specific legal rights, and
Purchaser may also have other rights which vary by jurisdiction.
All third party software provided with the Product is provided “AS IS”.
Purchaser assumes the entire risk as to the quality, performance, accuracy
and effect of such software, and should it prove defective, Purchaser, and not
Manufacturer, assumes the entire cost of all necessary servicing or repair.
16
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL MANUFACTURER BE
LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, HOWEVER CAUSED
REGARDLESS OF THE THEORY OF LIABILITY, ARISING OUT OF OR RELATED TO THE
USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF MANUFACTURER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL MANUFACT-
URER’S LIABILITY EXCEED THE AMOUNT PAID BY PURCHASER FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty or remedy provided
under this Agreement fails of its essential purpose. Some jurisdictions do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to Purchaser.
Twenty20 Disclaimer
All purchasers, users, and any or all parties involved or engaging in the use of
Twenty20, Inc (“Twenty20”) products agree to the following:
s
Twenty20 does not promote or endorse high risk, careless and/or dangerous
activities and is not responsible for any injury during use of ContourHD.
ContourHD primary purpose is recording legal activities as defined by
s
local authorities and Twenty20 is not liable for any use or misuse.
17
All trademarks and registered trademarks mentioned herein are
recognized as the property of their respective holders.
ContourHD is a product of Twenty20 Corporation in Seattle Washington
All rights reserved.
|